NatHERS Thermal Bridging: 4 Framing Weak Points Dragging Down Your Star Rating
Thermal bridging rarely gets the attention insulation and glazing do, yet it can quietly undo the work a well-specified design has already done to earn a strong NatHERS rating. A thermal bridge is any point in a building’s structure where heat moves more easily than through the surrounding insulated envelope, and framing is where most of them live. Thermal performance depends on far more than a single insulation number, and understanding thermal bridging properly, and where it actually shows up in a typical design, is one of the more overlooked levers for protecting a NatHERS star rating. Torple’s 7-star compliance service and BASIX assessment service both build this checking into the standard assessment process.
What Is Thermal Bridging, and Why Does This Matter for Ratings?
It happens wherever a more conductive material, most often structural framing, creates a path through the building envelope that bypasses the insulation around it. NCC 2022 made thermal bridging calculations mandatory for this kind of assessment, requiring assessors to model the effect on repeating steel frame elements in walls, floors and ceilings rather than treating framing as thermally neutral. That single change means a design’s framing choices now show up directly in the numbers behind a NatHERS star rating, not just its insulation specification.

Weak Point 1: Steel Framing Without Thermal Breaks
Steel is the clearest source of thermal bridging in Australian residential construction, since it conducts heat far more readily than timber or insulation, and its impact on overall thermal performance can be significant if left unaddressed. Where steel studs, joists or lintels sit in direct contact with external cladding or internal lining, heat finds a path straight through the frame, bypassing the batt insulation between the studs entirely. NCC 2022 addresses this by requiring thermal breaks with a minimum R-value of R0.2 at points of contact between steel framing and cladding, and a NatHERS rating calculated without them will reflect the performance penalty directly.
Weak Point 2: Corner Studs and the Timber Framing Factor
Timber framing is not immune either, even though it sits outside the formal steel-specific calculation. Corner studs, where two or three timber members are doubled or tripled up to provide structural support, replace what would otherwise be insulated cavity with solid timber, a genuine thermal bridging effect even though it is handled through general framing factor assumptions rather than the dedicated steel calculation. A design with more corners, and therefore more doubled-up studs, carries more of this effect than a simple rectangular floor plan, regardless of framing material.
Weak Point 3: Window and Door Reveals
Window and door openings interrupt wall insulation by necessity, and the reveal around each opening is a common, underappreciated thermal bridging point affecting overall thermal performance. Lintels above openings, particularly where steel is used to span a wide opening, concentrate the same conductive path problem seen in steel stud framing, just at a smaller scale. A design with generous glazing, which is otherwise good for daylight and passive solar performance, multiplies the number of these junctions across a floor plan.
Weak Point 4: Slab Edges and Balcony Penetrations
Where a concrete slab or balcony penetrates the building envelope, commonly in apartments, split-level homes or cantilevered outdoor areas, it creates a direct, continuous heat path from inside to outside with no insulation layer interrupting it at all, a scenario Torple’s Section J compliance service also encounters on mixed-use commercial and residential projects. This kind of thermal bridging is particularly costly in winter, since concrete conducts heat efficiently and the affected area can be substantial on a design with multiple balconies or a split floor level, another genuine drag on a NatHERS rating that has nothing to do with steel framing at all.
Why the Calculation Only Formally Covers Steel
It is worth understanding a genuine nuance here rather than treating all four weak points identically. The mandatory calculation applies specifically to repeating steel frame elements, using a methodology set out in the NatHERS Technical Note that calibrates a steel-framed home’s modelled thermal performance to align with an equivalent timber-framed design, rather than reflecting steel’s true, worse real-world thermal performance directly. Assessors can offset this by adding thermal breaks or improving other elements of the design. The other three weak points described here are real and affect actual comfort and energy use, but they are captured through general framing factor and junction assumptions in the software rather than this specific, named calculation.
How Much Can This Cost Your NatHERS Star Rating?
The star rating penalty from unaddressed framing weak points varies by design and climate zone or how much steel framing or glazing a project uses, but assessors regularly see this shift a marginal design across a star rating boundary on its own. A design sitting just below a required NatHERS rating threshold, checked against the official NatHERS guidance, is exactly the kind of project where checking these four weak points first, before reaching for more insulation elsewhere, tends to be the more cost-effective fix.
Early Thermal Modelling: Fixing Weak Points Before They’re Built
Early thermal modelling catches these weak points while they are still cheap to change, a thermal break specification, a lintel material choice, or a slab edge detail, rather than after construction drawings are finalised. An assessor engaged during design development, testing realistic thermal performance scenarios against the actual design, can flag which of a project’s own framing weak points is actually driving the rating down, rather than guessing and over-specifying insulation elsewhere to compensate for a problem insulation cannot fix.

Final Thoughts
These four weak points are not a single, uniform problem, they each affect a NatHERS star rating differently, and only one of them triggers this specific mandatory calculation. Torple’s thermal performance assessment service, thermal modelling service, 7-star compliance service and ESD reporting service can identify which of these weak points is actually affecting a specific design before construction locks them in, and Torple’s Insights hub covers related NatHERS topics in more depth. For the official technical detail, see the official guidance and the ABCB’s NCC hub.
FAQS
Thermal bridging is heat bypassing insulation through a more conductive path, most often structural framing. It affects this kind of assessment because NCC 2022 requires assessors to model this effect for steel framing directly, changing the calculated star rating.
NCC 2022 introduced the requirement because framing was previously treated as thermally neutral in modelling, understating real heat loss through steel elements. Mandatory calculation makes a NatHERS rating reflect framing choices more accurately.
It varies by design, but these weak points regularly shift a marginal project across a star rating boundary, particularly where a design combines steel framing, extensive glazing and slab edge or balcony penetrations together.
Thermal breaks with a minimum R-value of R0.2 at steel framing contact points, careful lintel material selection at window and door openings, and insulated slab edge details where concrete penetrates the envelope all directly address these weak points.
Yes. Early modelling can identify whether a targeted thermal break, a different lintel material, or better slab edge detailing resolves the issue, often avoiding the need to redesign the framing itself or over-specify insulation elsewhere.

